Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Error read fan speed on m/b ASUS A7V600
#1
I have m/b ASUS A7V600 and 5400 rpm 80x80 mm CPU fan. See value Fan4 163 rpm, real this sensors use EVERESRT I see real fan rpm - 5233. This calculation error.


Attached Files
.zip   reports.zip (Size: 120.63 KB / Downloads: 157)
Reply
#2
Thanks for your report.
Please attach the Debug File from HWiNFO32 too. Then I can fix it.

VictorVG Wrote:I have m/b ASUS A7V600 and 5400 rpm 80x80 mm CPU fan. See value Fan4 163 rpm, real this sensors use EVERESRT I see real fan rpm - 5233. This calculation error.
Reply
#3
Ok! I send to full reportn. don't include MAC/IP adress. I I choice anover hardware configuratin, this system don't stable - drivers for ATAPI/VIA RAID can generated kernel panic errror. This errir I see also on MS Windows and FreeBSD UNIX 6.4 - 8.0-STABLE p2 include FreeBSD fork PC-BSD 1.50 - 8.0, SUN Solaris 10/5 - 10/9 operating systems. LINUX kernel I don't like and not testing - I work on DEC service center as servis engeneer on DEC Alpha AXP systems.


Attached Files
.zip   reports_include_debug.zip (Size: 103.24 KB / Downloads: 128)
Reply
#4
Sorry, what full report? I need the Debug File when running HWiNFO32 in Debug Mode. You can find instuctions how to do this in this forum.
VictorVG Wrote:Ok! I send to full reportn. don't include MAC/IP adress.
Reply
#5
Attached on previonis post. Sorry on delay - my users send me many moderators qestions - I is moderator on some resource, and personal time is zero. Sad
Reply
#6
Please try the following build:
http://www.hwinfo.sk/beta/hw32_343_625.zip
and let me know how it works.

VictorVG Wrote:Attached on previonis post. Sorry on delay - my users send me many moderators qestions - I is moderator on some resource, and personal time is zero. Sad
Reply
#7
Sorry, not stable read. I have hardware error? I uses DC cooler Titan TFD-8025TH12X. Standard work speed 5400 rpm. BIOS/Lavalys EVEREST read sensor on this fan stable, but HWiNFO32 read this sensor periodically?


Attached Files
.zip   reports.zip (Size: 176.79 KB / Downloads: 132)
.rar   HWiNFO32.rar (Size: 20.2 KB / Downloads: 1)
Reply
#8
Are you running another sensor monitoring application in the background too? If yes, could you try to run only HWiNFO32?
Reply
#9
No. I know this effect, and running only one monitoring software at every time.
Reply
#10
I added new report, driver list XMl (source is Pserv.CPL 2.7) and old System log - disk error - I recovery controller PCB on this disk WDC2500 - disk periodical switching to "IDE Master" mode and call collision to WDC400 HDD on some IDE bus if jamper's settings choice on "Cable select" mode. I idon't know, but if hwinfo32 driver can't read SMBus data?


Attached Files
.zip   reports.zip (Size: 30.96 KB / Downloads: 151)
Reply
#11
Please try this build:
http://www.hwinfo.sk/beta/hw32_343_628.zip
and let me know if the fan reading is stable and ok.
Reply
#12
Test report:

1) clean run only beta 2.43.628. Sensor CPU fan not read;
2) run Everes, read sensors, make log, unload, run HWiNFO32 2.43.628 beta - CPU fan sensor detected, but periodicaly. I check this fan - is hardware defect ???

Reports include debug data attached


Attached Files
.zip   reports.zip (Size: 102.31 KB / Downloads: 144)
Reply
#13
Can you please make and attach a Debug File of the Clean Run (when HWiNFO32 doesn't find the CPU fan)?
It is possible that the CPU fan in not configured properly after boot.
Reply
#14
I think the problems is as I said - the fans are not properly configured by default.
Please try this build and let me know:
http://www.hwinfo.sk/beta/hw32_343_632.zip
Reply
#15
Beta 632 work Ok! Thanks!

Added:

Hardware defect found - this fan periodically not sanded signal on speed sensor, and BIOS can't read it. I lake replace this fan than choice free time. Big Grin

Aditional notes:

Chip ITE IT8712F, rev. G have only free fan sensor. I found base hardware specification on this chip family on to vendor suite <!-- m --><a class="postlink" href="http://www.ite.com.tw/EN/products_more.aspx?CategoryID=3&ID=5,66">http://www.ite.com.tw/EN/products_more. ... =3&ID=5,66</a><!-- m -->. Is is information data.

Thanks for bug fix!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)