[solved] Z77X-D3H/Z77X-UP5 - Printable Version
+- HWiNFO/32/64 Forum (http://www.hwinfo.com/forum)
+-- Forum: Bug Reports (/Forum-Bug-Reports)
+--- Forum: HWiNFO32 & HWiNFO64 Bug Reports (/Forum-HWiNFO32-HWiNFO64-Bug-Reports)
+--- Thread: [solved] Z77X-D3H/Z77X-UP5 (/Thread-Solved-Z77X-D3H-Z77X-UP5)
Z77X-D3H/Z77X-UP5 - stasio - 04-06-2012 10:32 AM
just testing Z77X-D3H and notice that sensor reading are wrong.
RE: Z77X-D3H - Martin - 04-06-2012 10:46 AM
I haven't yet performed sensor adjustments for Gigabyte 7-series mainboards.
Please attach also the HWiNFO Debug File (including sensor data) and it would be great to get a photo of what BIOS values are reported, or even better a screenshot of the Gigabyte EasyTune tool. Then I can determine what needs to be done.
RE: Z77X-D3H - stasio - 04-06-2012 10:54 AM
Pic is here:
How to take HWiNFO Debug File (including sensor data)?
RE: Z77X-D3H - Martin - 04-06-2012 11:11 AM
For the Debug File, you need to enable Debug Mode in settings, then run, open sensors and close HWiNFO.
See also this about submitting info: http://www.hwinfo.com/forum/Thread-IMPORTANT-Read-this-before-submitting-a-report
RE: Z77X-D3H - stasio - 04-06-2012 11:23 AM
enabled Debug Mode in settings,reset preference...still cann't found debug mode.
RE: Z77X-D3H - Martin - 04-06-2012 11:31 AM
You need to run the entire HWiNFO, open sensors, then close and then locate the HWiNFO64.DBG file.
RE: Z77X-D3H - Martin - 04-06-2012 11:49 AM
This build should fix it:
RE: Z77X-D3H - stasio - 04-06-2012 11:50 AM
(04-06-2012 11:31 AM)Martin Wrote: You need to run the entire HWiNFO, open sensors, then close and then locate the HWiNFO64.DBG file.
Now attachment problem to add.
With 1570,reading is better.
DBG file is here:
RE: Z77X-D3H - Martin - 04-06-2012 12:07 PM
If you pack the DBG it should be possible to attach it.
So is Build 1570 displaying all correct now including the chipset model?
RE: Z77X-D3H - stasio - 04-06-2012 12:19 PM
Yes,I zip DBG before.
RAM Vdimm is lower.
Here is pic :
RE: Z77X-D3H - Martin - 04-06-2012 12:34 PM
Can you please make at least 2 (3 would be even better) different shots of both HWiNFO and EasyTune where the DDR voltage is different? Just wait a bit and catch the right moment. I need to comapre if there needs to be a certain offset applied.
RE: Z77X-D3H - Martin - 04-06-2012 12:38 PM
Also one more question - is there a CHiL CHLxxxx chip on the mobo? If yes, could you please tell me the model number? It seems I need to adjust that one too (especially the VOUT is not correct).
RE: Z77X-D3H - stasio - 04-06-2012 01:30 PM
For chip CHiL ,I must search later(to small).
One more pic of System summary:
RE: Z77X-D3H - Martin - 04-06-2012 02:53 PM
Thanks. It seems there needs to be an offset applied to VDIMM.
I'll fix that together with the CHiL VOUT in next build if I get the required info on model. Maybe you could make a photo of the CHL chip?
Also, do you think the VTT reported by HWiNFO sensors is correct?
RE: Z77X-D3H - stasio - 04-06-2012 03:30 PM
Yes ,Vtt is correct.
I'll try to found info about CHiL.
Here is UD5H deep preview:
Also AIDA64 sensor are "Off",here is my post and report:
RE: Z77X-D3H - Martin - 04-06-2012 06:22 PM
I've seen that review.. The UD5H might however use a different VR than the D3H.
RE: Z77X-D3H - Martin - 04-06-2012 07:59 PM
Here the next build with further improvements:
RE: Z77X-D3H - stasio - 04-06-2012 09:36 PM
1571 voltage match with ET6 (AIDA64 not yet):
RE: Z77X-D3H - Martin - 04-06-2012 09:46 PM
Thanks for the feedback Now all seems fine, I'll do the same with GIGABYTE H77 series too.
If you get a chance to determine the VR model used (CHiL CHLxxxx or different), please let me know.
AIDA64 will be updated soon as well we're closely cooperating on many topics (including this one)
RE: Z77X-D3H - stasio - 04-06-2012 10:30 PM
I'll look for CHiL sensor.
Yes, I know that you and Tamas close cooperate.