[solved] Z77X-D3H/Z77X-UP5

[stasio]

Hi Martin,

just testing Z77X-D3H and notice that sensor reading are wrong.
report attached,
rgs

[Martin]

I haven't yet performed sensor adjustments for Gigabyte 7-series mainboards.
Please attach also the HWiNFO Debug File (including sensor data) and it would be great to get a photo of what BIOS values are reported, or even better a screenshot of the Gigabyte EasyTune tool. Then I can determine what needs to be done.

[stasio]

Pic is here:
http://i11.aijaa.com/b/00047/9941309.jpg
How to take HWiNFO Debug File (including sensor data)?
Thanks.

[Martin]

Thanks.
For the Debug File, you need to enable Debug Mode in settings, then run, open sensors and close HWiNFO.
See also this about submitting info: http://www.hwinfo.com/forum/Thread-IMPOR...g-a-report

[stasio]

Hmm,
enabled Debug Mode in settings,reset preference...still cann't found debug mode.

[Martin]

You need to run the entire HWiNFO, open sensors, then close and then locate the HWiNFO64.DBG file.

[Martin]

This build should fix it:
http://www.hwinfo.com/beta/hw64_394_1570.zip

[stasio]

You need to run the entire HWiNFO, open sensors, then close and then locate the HWiNFO64.DBG file.

OK,I got.
Now attachment problem to add.

---

With 1570,reading is better.
DBG file is here:
http://www.mediafire.com/?jp4s5cpjeprlbdy

[Martin]

If you pack the DBG it should be possible to attach it.
So is Build 1570 displaying all correct now including the chipset model?

[stasio]

Yes,I zip DBG before.
RAM Vdimm is lower.
Here is pic :
http://i11.aijaa.com/b/00953/9942070.jpg

[Martin]

Can you please make at least 2 (3 would be even better) different shots of both HWiNFO and EasyTune where the DDR voltage is different? Just wait a bit and catch the right moment. I need to comapre if there needs to be a certain offset applied.

[Martin]

Also one more question - is there a CHiL CHLxxxx chip on the mobo? If yes, could you please tell me the model number? It seems I need to adjust that one too (especially the VOUT is not correct).

[stasio]

For chip CHiL ,I must search later(to small).
One more pic of System summary:
http://i6.aijaa.com/b/00203/9942598.jpg

4GHz:
http://i1.aijaa.com/b/00401/9942786.jpg

Vdimm:
http://i6.aijaa.com/b/00206/9943413.jpg

[Martin]

Thanks. It seems there needs to be an offset applied to VDIMM.
I'll fix that together with the CHiL VOUT in next build if I get the required info on model. Maybe you could make a photo of the CHL chip?
Also, do you think the VTT reported by HWiNFO sensors is correct?

[stasio]

Yes ,Vtt is correct.
I'll try to found info about CHiL.
Thanks.

Edit:
Here is UD5H deep preview:
http://forums.tweaktown.com/gigabyte/479...eview.html

Also AIDA64 sensor are "Off",here is my post and report:
http://forums.aida64.com/index.php?/topi...#entry4348

[Martin]

I've seen that review.. The UD5H might however use a different VR than the D3H.

[Martin]

Here the next build with further improvements:
http://www.hwinfo.com/beta/hw64_394_1571.zip

[stasio]

Thanks,
1571 voltage match with ET6 (AIDA64 not yet):
http://i5.aijaa.com/b/00386/9946959.jpg

[Martin]

Thanks for the feedback Now all seems fine, I'll do the same with GIGABYTE H77 series too.
If you get a chance to determine the VR model used (CHiL CHLxxxx or different), please let me know.

AIDA64 will be updated soon as well we're closely cooperating on many topics (including this one)

[stasio]

I'll look for CHiL sensor.
Yes, I know that you and Tamas close cooperate.
Thanks Martin.