Recent content by Sergey

  1. S

    HP Workstation Z440 - FANs don't show

    Version "HWiNFO64 v5.32" works without problems. I attached the new debug file with 7 min. of operation of the program. HWiNFO  hangs on "Checking PCI".
  2. S

    HP Workstation Z440 - FANs don't show

    I attached the debug file and the HWiNFO64A.SYS file which is created in the temp directory. The file sizes are too small to be so loud cracked head hdd and the program crashed. When it starts crackling the hdd, volumes of files does not increase. So at this time no data is written. That is...
  3. S

    HP Workstation Z440 - FANs don't show

    Thanks. All sensors show correctly. I attached the debug file. Problem with hanging on startup when selecting the "Debug Write Direct" option was left. Please fix it, because previously versions with this option the debug mode worked fine.
  4. S

    HP Workstation Z440 - FANs don't show

    Ok. Resume. I ran HWiNFO / HP separately and compared the results. 1. There is correct: the CPU temperature, the front/rear fans. 2. There is incorrect: the CPU fan, the memory fan, the Ambient temperature. I disabled the "Debug Write Direct" option and the HWiNFO program starts without...
  5. S

    HP Workstation Z440 - FANs don't show

    I compared online HP Performance Advisor and HWiNFO. 1. The CPU temperature is correct. 2. Everything else shows is not true. - The CPU fan: 687 rpm (HP Performance Advisor) and 176 (HWiNFO) - The front fan: 689 rpm (HP Performance Advisor) and 945 (HWiNFO) - The rear fan: 820 rpm (HP...
  6. S

    HP Workstation Z440 - FANs don't show

    1. I have attached a screen shot from HP Performance Advisor. Memory fan = 0 (this module is not installed). 2. I run HWiNFO from a HDD. 3. I waited 1 minute, but the program hung on the analysis of the devices. The hard drive is very loud cracked heads.
  7. S

    HP Workstation Z440 - FANs don't show

    1. The program is run in normal mode. I see a new sensor called "HP EC", but the values are not correct. I have attached a screen shot. 2. The program hangs at startup in debug mode. Hard drive clicks heads continuously. I have attached the debug file.
  8. S

    HP Workstation Z440 - FANs don't show

    I attached the debug file. I haven't seen a new sensor called "HP EC".
  9. S

    HP Workstation Z440 - FANs don't show

    I attached the SMBIOS file still where I saw the information about the fans.
  10. S

    HP Workstation Z440 - FANs don't show

    I attached the file.
  11. S

    HP Workstation Z440 - FANs don't show

    I attached the files. I see the fan data in the "AcpiTbls (RW-Everything tool).txt" file.
  12. S

    HP Workstation Z440 - FANs don't show

    HP Performance Advisor show fan speeds. It show too: PortConnector Type = 8 Marker = 53 Formatted length = 9 0000: 08 09 35 00 01 FF 00 00 0008: FF Unformatted length = 13 0000: 50 38 20 43 50 55 30 20 [ P 8 C P U 0 ] 0008: 46 41 4E 00 00 [ F A N \0 \0 ]...
  13. S

    HP Workstation Z440 - FANs don't show

    Thank you. Why the information about fan speeds is not transmitted? Is it a problem of BIOS or Windows 10? Where to look for the problem?
  14. S

    HP Workstation Z440 - FANs don't show

    I attached the debug file. I tested SpeedFAN but it don't show too.
  15. S

    HP Workstation Z440 - FANs don't show

    HP Workstation Z440: 1. Motherboard Model:   Hewlett-Packard 212B 2. Motherboard Chipset: Intel C612 (Wellsburg-G) 3. OS Windows 10 Pro 4. HWiNFO64 v5.32 for Windows (Native 64-bit) It's a problem: FANs don't show on the sensor status panel. Only GPU FAN show.
Top