Newbie question: harddisks: Power on counts &- Hours in use

[Mike991]

Newbie question...
Most probably I am overlooking it, but I would like to know if HWiNFO can provide information about

- number of times drives have been powered on
- hours (days/hours) in use

Thanks!

=

 

[Martin]

HWiNFO provides this information in raw format only in the main window under drives, S.M.A.R.T.

 

[Mike991]

HWiNFO provides this information in raw format only in the main window under drives, S.M.A.R.T.

Ah, I see ... many thanks for the quick feedback!

==
[01] Raw Read Error Rate: 200/47, Worst: 200
[03] Spin Up Time: 228/39, Worst: 227 (Data = 8566)
[04] Start/Stop Count: 97/50, Worst: 97 (Data = 3500)
[05] Reallocated Sector Count: 200/51, Worst: 200
[07] Seek Error Rate: 100/46, Worst: 253
[09] Power-On Hours/Cycle Count: 70/50, Worst: 70 (Data = 21968)
[0A] Spin Retry Count: 100/50, Worst: 100
[0B] Calibration Retry Count: 100/50, Worst: 100
[0C] Power Cycle Count: 97/50, Worst: 97 (Data = 3183)
[C0] Power-Off Retract Count: 200/50, Worst: 200 (Data = 101)
[C1] Load/Unload Cycle Count: 199/50, Worst: 199 (Data = 3500)
[C2] Temperature 119/34, Worst: 110 (Data = 31.0 °C)
[C4] Reallocation Event Count: 200/50, Worst: 200
[C5] Current Pending Sector Count: 200/50, Worst: 200
[C6] Off-Line Uncorrectable Sector Count: 200/48, Worst: 200
[C7] UltraDMA/SATA CRC Error Rate: 200/50, Worst: 200
[C8] Write/Multi-Zone Error Rate: 200/8, Worst: 200

==
I checked with another tool for verification (which figure to consider), because frankly speaking "97/50 worst: 97", well I am not familiar with that, -no- offense meant, of course.

=from another tool=
[attachment=1142]
=

Anyway, thanks again!

 

[Martin]

I can adjust the Power-On Hours value to show in days/years respectively.

 

[Mike991]

I can adjust the Power-On Hours value to show in days/years respectively.

As for me, to be honest...
yes - if it is feasable, it would indeed be nice: it is a bit more, let's say, 'understandable' than 70/50, Worst: 70 - 97/50, Worst: 97.

Thanks.
=

 

[Mike991]

Any developments on this one?
I may be overlooking it, but I think in 5.13-2765 it is not yet implemented...
Again, maybe I should look in a different section.

It would be nice to have
Power On Count: nnnn
Power On Hours: nnnnnn

Thanks!
=
=

 

[Martin]

It is implemented in the main window: Drive - S.M.A.R.T. status. I have improved decoding of those items as mentioned above.

 

[Mike991]

RE: Newbie question: harddisks: Power on counts &- Hours in use

Ai!

:blush:  Ahum.... :blush:


I didn't send anything, right..?

My wife sometimes says: READ!!
(oh, I hate such moments, cause she often she is right)
extremely poor excuse this time, I was expecting a number, so I didn't _read_ any further.

=

 

[Martin]

No problem - I often have the same problem with "you just don't listen to me!"