Error read fan speed on m/b ASUS A7V600

VictorVG

Well-Known Member
I have m/b ASUS A7V600 and 5400 rpm 80x80 mm CPU fan. See value Fan4 163 rpm, real this sensors use EVERESRT I see real fan rpm - 5233. This calculation error.
 

Attachments

  • reports.zip
    120.6 KB · Views: 157
Thanks for your report.
Please attach the Debug File from HWiNFO32 too. Then I can fix it.

VictorVG said:
I have m/b ASUS A7V600 and 5400 rpm 80x80 mm CPU fan. See value Fan4 163 rpm, real this sensors use EVERESRT I see real fan rpm - 5233. This calculation error.
 
Ok! I send to full reportn. don't include MAC/IP adress. I I choice anover hardware configuratin, this system don't stable - drivers for ATAPI/VIA RAID can generated kernel panic errror. This errir I see also on MS Windows and FreeBSD UNIX 6.4 - 8.0-STABLE p2 include FreeBSD fork PC-BSD 1.50 - 8.0, SUN Solaris 10/5 - 10/9 operating systems. LINUX kernel I don't like and not testing - I work on DEC service center as servis engeneer on DEC Alpha AXP systems.
 

Attachments

  • reports_include_debug.zip
    103.2 KB · Views: 128
Sorry, what full report? I need the Debug File when running HWiNFO32 in Debug Mode. You can find instuctions how to do this in this forum.
VictorVG said:
Ok! I send to full reportn. don't include MAC/IP adress.
 
Attached on previonis post. Sorry on delay - my users send me many moderators qestions - I is moderator on some resource, and personal time is zero. :(
 
Sorry, not stable read. I have hardware error? I uses DC cooler Titan TFD-8025TH12X. Standard work speed 5400 rpm. BIOS/Lavalys EVEREST read sensor on this fan stable, but HWiNFO32 read this sensor periodically?
 

Attachments

  • reports.zip
    176.8 KB · Views: 132
  • HWiNFO32.rar
    20.2 KB · Views: 1
Are you running another sensor monitoring application in the background too? If yes, could you try to run only HWiNFO32?
 
I added new report, driver list XMl (source is Pserv.CPL 2.7) and old System log - disk error - I recovery controller PCB on this disk WDC2500 - disk periodical switching to "IDE Master" mode and call collision to WDC400 HDD on some IDE bus if jamper's settings choice on "Cable select" mode. I idon't know, but if hwinfo32 driver can't read SMBus data?
 

Attachments

  • reports.zip
    31 KB · Views: 151
Test report:

1) clean run only beta 2.43.628. Sensor CPU fan not read;
2) run Everes, read sensors, make log, unload, run HWiNFO32 2.43.628 beta - CPU fan sensor detected, but periodicaly. I check this fan - is hardware defect ???

Reports include debug data attached
 

Attachments

  • reports.zip
    102.3 KB · Views: 144
Can you please make and attach a Debug File of the Clean Run (when HWiNFO32 doesn't find the CPU fan)?
It is possible that the CPU fan in not configured properly after boot.
 
Beta 632 work Ok! Thanks!

Added:

Hardware defect found - this fan periodically not sanded signal on speed sensor, and BIOS can't read it. I lake replace this fan than choice free time. :D

Aditional notes:

Chip ITE IT8712F, rev. G have only free fan sensor. I found base hardware specification on this chip family on to vendor suite <!-- m --><a class="postlink" href="http://www.ite.com.tw/EN/products_more.aspx?CategoryID=3&ID=5,66">http://www.ite.com.tw/EN/products_more. ... =3&ID=5,66</a><!-- m -->. Is is information data.

Thanks for bug fix!
 
Back
Top